View MC10E154_88330.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
5 Bit 2:1 Mux Latch
The MC10E/100E154 contains five 2:1 multiplexers followed by transparent latches with differential outputs. When both Latch Enables (LEN1, LEN2) are LOW, the latch is transparent, and output data is controlled by the multiplexer select control, SEL. A logic HIGH on either LEN1 or LEN2 (or both) latches the outputs. The Master Reset (MR) overrides all other controls to set the Q outputs LOW.
MC10E154 MC100E154
5-BIT 2:1 MUX-LATCH
* * * * * * *
850ps Max. LEN to Output 825ps Max. D to Output Differential Outputs Asynchronous Master Reset Dual Latch-Enables Extended 100E VEE Range of - 4.2V to - 5.46V 75k Input Pulldown Resistors
Pinout: 28-Lead PLCC (Top View)
D4b 25 SEL LEN1 LEN2 VEE MR D0a D0b 26 27 28 1 2 3 4 5 D1a 6 D1b 7 D2a 8 9 10 Q0 11 Q0 D4a 24 D3b 23 D3a VCCO 22 21 Q4 20 Q4 19 18 17 16 15 14 13 12 Q3 Q3
FN SUFFIX PLASTIC PACKAGE CASE 776-02
LOGIC DIAGRAM
VCC D0a Q2 Q2 Q1 Q1 D1a D1b MUX SEL Q D EN Q R Q D EN Q R Q D EN Q R Q1 Q1 D0b MUX SEL Q D EN Q R Q0 Q0
D2a D2b D3a
MUX SEL
Q2 Q2
D2b VCCO
* All VCC and VCCO pins are tied together on the die. MUX SEL Q3 Q3
PIN NAMES
Pin D0a - D4a D0b - D4b SEL LEN1, LEN2 MR Q0 - Q4 Q0 - Q4 Function Input Data a Input Data b Data Select Input Latch Enables Master Reset True Outputs Inverted Outputs
D3b D4a D4b
MUX SEL
Q D EN Q R
Q4 Q4
SEL LEN1 LEN2
TRUTH TABLE
SEL H L
12/93
Data a b
MR
(c) Motorola, Inc. 1996
2-1
REV 2
MC10E154 MC100E154
DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0C Symbol IIH IEE Characteristic Input HIGH Current Power Supply Current 10E 100E 76 76 min typ max 150 91 91 76 76 min 25C typ max 150 91 91 76 87 min 85C typ max 150 91 105 Unit A mA Condition
AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0C Symbol tPLH tPHL Characteristic Propagation Delay to Output D SEL LEN MR Setup Time D SEL Hold Time D SEL Reset Recovery Time Minimum Pulse Width MR Within-Device Skew Rise/Fall Times 20 - 80% 300 min 325 475 350 450 300 500 300 200 800 400 50 475 800 300 typ 500 650 500 600 100 250 -100 - 250 600 max 700 925 750 800 min 325 475 350 450 300 500 300 200 800 400 50 475 800 300 25C typ 500 650 500 600 100 250 -100 - 250 600 max 700 925 750 800 min 325 475 350 450 300 500 300 200 800 400 50 475 800 ps ps 1 85C typ 500 650 500 600 100 250 ps -100 - 250 600 ps ps max 700 925 750 800 ps Unit ps Condition
ts
th
tRR tPW tSKEW tr tf
1. Within-device skew is defined as identical transitions on similar paths through a device.
MOTOROLA
2-2
ECLinPS and ECLinPS Lite DL140 -- Rev 4
MC10E154 MC100E154
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 776-02 ISSUE D
0.007 (0.180) U T L -M
M
B -NY BRK
M
S
N
S S
0.007 (0.180)
T L -M
N
S
D Z -L-M-
W
28 1
D X VIEW D-D G1 0.010 (0.250)
S
V
T L -M
S
N
S
A Z R
0.007 (0.180) 0.007 (0.180)
M
T L -M T L -M
S
N N
S
H
S
0.007 (0.180)
M
T L -M
S
N
S
M
S
C
E G G1 0.010 (0.250)
S
K1 0.004 (0.100) J -TSEATING PLANE
K F VIEW S 0.007 (0.180)
M
VIEW S T L -M
S
T L -M
S
N
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIM G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIM R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 -- 0.025 -- 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 -- 0.020 2 10 0.410 0.430 0.040 --
MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 -- 0.64 -- 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 -- 0.50 2 10 10.42 10.92 1.02 --
ECLinPS and ECLinPS Lite DL140 -- Rev 4
2-3
MOTOROLA
MC10E154 MC100E154
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 2-4
*MC10E154/D*
MC10E154/D ECLinPS and ECLinPS Lite DL140 -- Rev 4

▲Up To Search▲

Price & Availability of MC10E154

	To Download MC10E154 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .